3Com 3CSFP81 Compatible 100M SFP Transceiver Module
Built for hosts recognizing 3CSFP81, this HT-manufactured SFP module delivers 100M transmission at 1310nm. Its rated reach is 2km, with Duplex LC as the physical interface. The specifications and engineering guidance below support procurement teams match an equipment parts list to a clearly defined optical product, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: 3CSFP81HT Part Number: 3CSFP81
Product Highlights
- Compatible alternative to 3Com 3CSFP81
- 100M connectivity at 100Mbps
- Optical wavelength: 1310nm
- Specified reach: 2km
- Duplex LC / MMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| 3Com Compatible | 3CSFP81 |
|---|---|
| Manufacturer | HT |
| HT Part Number | 3CSFP81 |
| Form Factor | SFP |
| Max Data Rate | 100Mbps |
| Wavelength | 1310nm |
| Max Cable Distance | 2km |
| Connector | Duplex LC |
| Optical Components | FP 1310nm |
| Media | MMF |
| DOM Support | Yes |
| TX Power | -15~-8dBm |
| Receiver Sensitivity | < -32dBm |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Protocols | IEEE802.3U, GR-468, MSA Compliant |
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The Duplex LC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100M interface configuration must match the remote equipment; sharing a SFP housing alone does not make two transceiver types interoperable.
The multimode channel should use the fiber grade associated with the stated 2km reach. Keep the Duplex LC end faces clean and avoid tight bends. Different multimode standards are not interchangeable merely because they share a connector.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -15~-8dBm; receiver sensitivity is < -32dBm. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Procurement and Asset Identification
A useful purchase order identifies the host platform, expected OEM code and optical standard separately. This prevents a module with the same housing but another wavelength, reach or identification profile from being substituted. For mixed deployments, keep one order line per OEM reference and reconcile each received unit with its intended port. For this model, the principal parameters are data rate 100Mbps, wavelength 1310nm, rated reach 2km.
3Com Compatibility and Factory Testing
Factory verification starts with the expected 3CSFP81 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Ordering Information
Quote HT part number 3CSFP81 together with OEM reference 3CSFP81 and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original 3Com transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies 3CSFP81, not an original 3Com-branded module.
Which fiber and connector are required?
Use Duplex LC with MMF. The specified maximum reach is 2km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.