800G OSFP (IHS/Finned Top) to 4x 200G OSFP (RHS/Flat Top)-800G-DAC-1M3FT 800G OSFP 8 x 100G PAM4 IHS/Finned Top to 4 x 200G OSFP 2 x 100G PAM4 RHS/Flat Top Passive Copper Breakout Cable, 1m (3ft)
This page gives procurement and network teams a precise reference for Generic 800G OSFP (IHS/Finned Top) to 4x 200G OSFP (RHS/Flat Top)-800G-DAC-1M3FT: a 800G DAC assembly in a fixed 1m (3ft) configuration. The 800G OSFP (IHS/Finned Top) to 4x 200G OSFP (RHS/Flat Top) interface, HT ordering identity and verified specifications are presented together so the required cable can be matched to the bill of materials without confusing it with another length.
OEM Part Number: 800G OSFP (IHS/Finned Top) to 4x 200G OSFP (RHS/Flat Top)-800G-DAC-1M3FTHT Part Number: 800G OSFP (IHS/Finned Top) to 4x 200G OSFP (RHS/Flat Top)-800G-DAC-1M3FT
Product Highlights
- HT-manufactured DAC assembly in 1m (3ft)
- 800G connectivity at 800Gbps
- Interface configuration: 800G OSFP (IHS/Finned Top) to 4x 200G OSFP (RHS/Flat Top)
- Fixed length and part number: 1m (3ft), 800G OSFP (IHS/Finned Top) to 4x 200G OSFP (RHS/Flat Top)-800G-DAC-1M3FT
- Cable construction: Passive Breakout DAC
- Conductor specification: 28AWG
- Maximum power consumption: 0.1W (800G End)0.1W (200G Per End)
- Minimum bend radius: 31mm
Specifications
| HT Part Number | 800G OSFP (IHS/Finned Top) to 4x 200G OSFP (RHS/Flat Top)-800G-DAC-1M3FT |
|---|---|
| Manufacturer | HT |
| Form Factor | 800G OSFP (IHS/Finned Top) to 4x 200G OSFP (RHS/Flat Top) |
| Max Data Rate | 800Gbps |
| Media | Copper |
| Cable Type | Passive Breakout DAC |
| Cable Length | 1m (3ft) |
| Wire AWG | 28AWG |
| Minimum Bend Radius | 31mm |
| Max. Power Consumption | 0.1W (800G End)0.1W (200G Per End) |
| Jacket Material | PVC |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Protocols | OSFP MSA, IEEE 802.3ck, CMIS v4.0 |
| Modulation Format | 8x 100G PAM4 to Quad 2x 100G PAM4 |
Signal and Lane Configuration
The listed modulation format is 8x 100G PAM4 to Quad 2x 100G PAM4. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.
Position Within the Length Range
800G OSFP (IHS/Finned Top) to 4x 200G OSFP (RHS/Flat Top)-800G-DAC-1M3FT occupies the middle of this family between 800G OSFP (IHS/Finned Top) to 4x 200G OSFP (RHS/Flat Top)-800G-DAC-0.5M2FT at 0.5m (2ft) and 800G OSFP (IHS/Finned Top) to 4x 200G OSFP (RHS/Flat Top)-800G-DAC-1.5M5FT at 1.5m (5ft). It adds 0.5m over the shorter option for extra routing clearance, while the next longer version adds another 0.5m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.
Procurement and Port-Mapping Review
A useful purchase order should identify the host platform, the expected OEM code and the exact cable length as separate pieces of information. This prevents a physically similar assembly from being substituted when the port identification or reach is different. For mixed-length installations, prepare one order line per part number and reconcile each delivered cable with its intended pair of ports. For this assembly, the listed conductor specification is 28AWG; the minimum bend radius is 31mm; the stated power consumption is 0.1W (800G End)0.1W (200G Per End); the jacket material is PVC.
Power and Thermal Planning
The rated power consumption is 0.1W (800G End)0.1W (200G Per End). Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.
Cable Construction and Routing
This assembly uses 28AWG conductors, PVC jacket, minimum bend radius 31mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.
Network and Protocol Considerations
The intended application is determined by the host interface and protocol support. Listed interface and protocol references include OSFP MSA, IEEE 802.3ck, CMIS v4.0. Confirm that the host firmware and port configuration support the same operating mode.
Breakout Port Mapping
The 800G OSFP (IHS/Finned Top) to 4x 200G OSFP (RHS/Flat Top) configuration divides the high-speed interface into multiple lower-speed connections. Verify the upstream lane assignment, downstream port speeds and breakout setting on the host before connecting the assembly. Each branch must attach to the correct remote interface.
Passive Copper Operation
A passive DAC has no separate optical conversion stage. Its low-power, low-latency operation is useful for short equipment links, but the assembly must remain within the length and signaling mode accepted by both hosts.
Length Selection and Installation Planning
At 1m (3ft), 800G OSFP (IHS/Finned Top) to 4x 200G OSFP (RHS/Flat Top)-800G-DAC-1M3FT is a practical choice for direct connections within one rack. Route the cable along the intended management path rather than pulling it diagonally across adjacent connectors, and leave enough clearance for insertion, removal and front-panel airflow.
Generic Compatibility and Factory Testing
Our procurement-oriented compatibility check begins with the OEM reference and ends with a live host link. We record the physical length separately from the identification configuration, so the cable supplied for this page remains the stated version rather than a generic length substitute. Where supported by the host, link stability and diagnostic indications are reviewed together with the established link.
Ordering Information
For a clear bill of materials, quote the OEM reference, HT part number, length and quantity on the same line. Add the switch or server model and software release when a pre-order review is required; project labels can repeat those details for receiving and installation teams. Quantity and any labeling instructions should be attached specifically to 800G OSFP (IHS/Finned Top) to 4x 200G OSFP (RHS/Flat Top)-800G-DAC-1M3FT.
Quality Assurance and Packaging
Before packing, the assembly is checked for connector condition, identification and link operation. Cables for multi-line orders can be labelled and grouped by part number, making it easier to match each length to the procurement record without opening every protective bag. Standard protective packing is used by default, with project documentation arranged when requested.
Frequently Asked Questions
Is this an original equipment manufacturer cable?
No. It is manufactured by HT under our own manufacturer identity.
What details assist a compatibility review?
Provide the equipment manufacturer, model, port type, hardware revision and software release, together with the OEM reference, required length and quantity.
How should an unused assembly be stored?
Protect both connector ends, keep the cable in a loose bend-safe coil and retain its part-number label so the length and compatibility identity remain traceable.
Can different brands be connected with the same assembly?
Only where both hosts explicitly support the complete interface and compatibility arrangement. Document each end and select the appropriate brand-specific product when required.
Shipping and Lead Time
Available stock is generally dispatched within one to three working days after order confirmation, with production lead times advised for larger quantities. Delivery can be arranged by courier, air freight or sea freight, and goods may instead be handed to an appointed forwarder or shipped on the customer’s courier account.