Juniper Networks CFP4-100GBASE-LR4 Compatible 100G CFP4 LR4 Transceiver Module
Built for hosts recognizing CFP4-100GBASE-LR4, this HT-manufactured CFP4 module delivers 100G transmission at 1295.56nm, 1300.05nm, 1304.58nm, 1309.14nm. Its rated reach is 10km, with its specified interface as the physical interface. The specifications and engineering guidance below support procurement teams match an equipment parts list to a clearly defined optical product, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: CFP4-100GBASE-LR4HT Part Number: CFP4-LR4-100G
Product Highlights
- Compatible alternative to Juniper Networks CFP4-100GBASE-LR4
- 100G connectivity at 112Gbps
- Optical wavelength: 1295.56nm, 1300.05nm, 1304.58nm, 1309.14nm
- Specified reach: 10km
- SMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| Juniper Networks Compatible | CFP4-100GBASE-LR4 |
|---|---|
| Manufacturer | HT |
| HT Part Number | CFP4-LR4-100G |
| Form Factor | CFP4 |
| Max Data Rate | 112Gbps |
| Wavelength | 1295.56nm, 1300.05nm, 1304.58nm, 1309.14nm |
| Max Cable Distance | 10km |
| Interface | LC duplex |
| Optical Components | 4x DFB |
| Media | SMF |
| DOM Support | Yes |
| Modulation (Electrical) | 4x 25G-NRZ |
| Modulation (Optical) | 4x 25G-NRZ |
| Protocols | MSA Compliant |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a CFP4 housing alone does not make two transceiver types interoperable.
The single-mode link budget should include fiber attenuation, connectors, splices and panels over the intended 10km route. Keep the interface clean and match the remote optical standard. Consider receiver overload as well as insufficient power on short links.
Optical Acceptance, Diagnostics and Handling
Use the electrical and optical limits in the specification table as the acceptance reference for this model. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Procurement and Asset Identification
A useful purchase order identifies the host platform, expected OEM code and optical standard separately. This prevents a module with the same housing but another wavelength, reach or identification profile from being substituted. For mixed deployments, keep one order line per OEM reference and reconcile each received unit with its intended port. For this model, the principal parameters are data rate 112Gbps, wavelength 1295.56nm, 1300.05nm, 1304.58nm, 1309.14nm, rated reach 10km.
Juniper Networks Compatibility and Factory Testing
The module is checked for host recognition as CFP4-100GBASE-LR4, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Ordering Information
Quote HT part number CFP4-LR4-100G together with OEM reference CFP4-100GBASE-LR4 and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Juniper Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies CFP4-100GBASE-LR4, not an original Juniper Networks-branded module.
Which fiber and connector are required?
Use the specified optical connector with SMF. The specified maximum reach is 10km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.