Juniper Networks EX-SFP-GE80KCW1270 Compatible 1G SFP Transceiver Module
Built for hosts recognizing EX-SFP-GE80KCW1270, this HT-manufactured SFP module delivers 1G transmission at 1270nm. Its rated reach is 80km, with Duplex LC as the physical interface. The specifications and engineering guidance below support procurement teams match an equipment parts list to a clearly defined optical product, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: EX-SFP-GE80KCW1270HT Part Number: CW-SFP1G80-27
Product Highlights
- Compatible alternative to Juniper Networks EX-SFP-GE80KCW1270
- 1G connectivity at 1000Mbps
- Optical wavelength: 1270nm
- Specified reach: 80km
- Duplex LC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | CW-SFP1G80-27 |
|---|---|
| Manufacturer | HT |
| Form Factor | SFP |
| Max Data Rate | 1000Mbps |
| Wavelength | 1270nm |
| Max Cable Distance | 80km |
| Connector | Duplex LC |
| Media | SMF |
| Transmitter Type | DFB CWDM |
| Receiver Type | APD |
| Receiver Sensitivity | 1270~1370nm (APD): -30/-31dBm1390~1610nm (PIN): -28/-29dBm |
| SMSR | 30dB |
| SMSR | 30dB |
| TX Power | 0~5dBm |
| RX Power | -30~-8dBm |
| Power Consumption | ≤1W |
| Power Budget | 24dB |
| EMC (Electro Magnetic Comnatihilitv) | Supported |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Protocols | SFP MSASFF-8472 |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 1G interface configuration must match the remote equipment; sharing a SFP housing alone does not make two transceiver types interoperable.
Wavelength-selective links require the exact channel plan at both ends. Confirm that filters pass 1270nm, then include their insertion loss in the 80km power budget. A nearby channel is not a substitute for the specified wavelength.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is 0~5dBm; receiver sensitivity is 1270~1370nm (APD): -30/-31dBm1390~1610nm (PIN): -28/-29dBm; the stated optical power budget is 24dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Procurement and Asset Identification
A useful purchase order identifies the host platform, expected OEM code and optical standard separately. This prevents a module with the same housing but another wavelength, reach or identification profile from being substituted. For mixed deployments, keep one order line per OEM reference and reconcile each received unit with its intended port. For this model, the principal parameters are data rate 1000Mbps, wavelength 1270nm, rated reach 80km.
Juniper Networks Compatibility and Factory Testing
Factory verification starts with the expected EX-SFP-GE80KCW1270 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Ordering Information
Quote HT part number CW-SFP1G80-27 together with OEM reference EX-SFP-GE80KCW1270 and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Juniper Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies EX-SFP-GE80KCW1270, not an original Juniper Networks-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 80km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.