Kenyan network installers should begin with the actual mating interfaces and site fiber records before assigning this product to a link. This fiber pigtail terminates outside-plant or backbone cable into a connectorized panel: LC UPC to Unterminated Fiber Pigtail, OS2 glass, with a factory-polished LC UPC connector on one end and a prepared fiber strand on the other. Fusion-spliced onto the incoming cable, it turns a raw fiber pathway into a documented, testable port.
Product Highlights
- Color-coded for Easy Matching of 0.9mm Fiber to Be Spliced
- Easy-strip 900µm Tight-buffered Coating
- Precision Zirconia Ferrule Connectors Ensure Low Loss
- Support Both Fusion and Mechanical Splicing
- G.657.A1 Bend Insensitive Fiber & 10mm Min. Bend Radius
Specifications
| Connector A | LC UPC Simplex |
|---|---|
| Connector B | Unterminated |
| Fiber Count | 12 Fibers |
| Fiber Grade | G.657.A1 |
| Fiber Mode | OS2 9/125μm |
| Wavelength | 1310/1550nm |
| Jacket Color | Yellow |
| Cable Jacket | PVC (Unrated) |
| Min. Bend Radius (Optical Fiber) | 10mm |
| Min. Bend Radius (Fiber Cable) | 10/5D (Dynamic/Static) |
| Connector Durability | 1000 Times |
| Tensile Strength (Long/Short Term) | 200/660N |
| Attenuation at 1310nm | 0.36dB/km |
| Attenuation at 1550nm | 0.22dB/km |
| Insertion Loss | ≤0.3dB |
| Return Loss | ≥50dB |
| Operating Temperature | -20 to 70°C (-4 to 158°F) |
| Storage Temperature | -40 to 70°C (-40 to 158℉) |
| Connector Type | LC UPC Simplex to Unterminated |
| Fiber Count | 12 Fibers |
From raw fiber route to documented port
Every structured cabling plant ends the matching way: a cable arrives at a frame, and its fibers must become ports. The pigtail is the component that makes that conversion. Spliced into a tray and presented on a panel, each strand gains a connector with a known optical signature, a slot in the documentation and a place in the test record. That conversion - cable to port - is where channel quality is won or lost.
Mechanical splicing as the field fallback
Where a fusion splicer is never obtainable, mechanical splices get the channel up: the strand cleaves, seats in the mechanical splice body and locks against the field fiber. Because the loss is higher than a fusion joint and the reflectance worse, the practice is a fallback rather than a standard - but for urgent restoration work a pigtail that supports both methods keeps the version open.
Keeping twelve-fiber splices organized
Multi-fiber splicing rewards method: full one color fully - strip, clean, cleave, splice, sleeve - before starting the next, and dress each finished strand into the tray in sequence. The color-coded set makes the pairing unambiguous, and the tray stays readable for the next technician who opens it. A tray that reads plainly is a tray that gets re-entered without new faults.
Color coding as a working discipline
Twelve fibers, twelve colors, one order: the TIA-598 sequence is the only thing standing between a tidy splice tray and a crossed plant. Because the strands in this set adhere to the standard sequence, the splicer matches colors between cable and pigtail without guesswork. When the documentation follows the matching sequence, a fault on slot seven months from now is found in minutes rather than traced strand by strand.
Unjacketed and bunch constructions compared
The unjacketed color-coded set presents twelve independent 0.9mm strands for direct tray work - the lightest structure and the easiest to dress. The bunch structure gathers the twelve strands under a shared jacket that breaks out near the optical connector end, adding handling protection on the pathway between the adapter panel and the tray. Pick unjacketed where the strands stay inside a protected enclosure; pick bunch where the cable assembly crosses open space between frames.
Bend-insensitive glass in dense trays
Splice trays and panel rear spaces punish fiber: tight routing, crowded dressing and the occasional hurried re-entry all bend strands beyond what legacy single-mode tolerated. The bend-insensitive grade used in this pigtail holds attenuation stable at bend radii that would fog conventional glass, which keeps the channel margin intact after the tenth tray opening, not just at commissioning.
Sparing and kit planning for termination work
Pigtails belong in the termination kit in counted sets with spares: strands break, connectors get contaminated beyond recovery, and a missing spare converts a ten-minute task into a second visit. Plan one spare set per frame slot, keep spare strands capped and bagged, and record which set went into which tray so replacement stock can usually be ordered to the identical specification.
A splicing workflow that scales
Productive termination crews work to a fixed routine: mount the tray, dress the optical cable, splice the pigtails color by color, protect each joint, test each completed port, then close and label. With the routine fixed, a two-person crew terminates a full frame slot in a predictable time, and the test record maps cleanly onto the documentation. The consistency further makes quality auditable - matching materials, matching sequence, matching pass criteria across every site.
Selecting the right pigtail for the job
Five decisions define the order: the optical connector range must match the adapter panel, the polish must match the plant, the fiber mode must match the optical cable, the structure must match the pathway, and the count must match the tray capacity. Getting all five right at order time is what turns a box of strands into a dependable termination. Where the specification sits outside the standard configurations, the project-specific platforms cover the remaining combinations.
Factory Testing and Quality Checks
Every pigtail is optically tested before packing: insertion loss and return loss are verified on each terminated leg, and the ferrule end faces are inspected for scratches and contamination. The strands ship coiled, capped and bagged, with the test results obtainable on ask for.
How to Order and Factory Support
Refer to this pigtail by connector, polish, fiber mode, fiber count and structure when asking for a quotation. For configurations outside the listed options - mixed connector families, jacket ratings, lengths or project packaging - send the specification with the request and the factory will check the manufacturable specification. Project support for Kenya and East Africa is available to reconcile the ordered configuration with the intended installation.