OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-20M66FT 400G OSFP 4 x 100G PAM4 RHS/Flat Top to 400G QSFP-DD 8 x 50G PAM4 Active Optical Cable, 20m (66ft)
For buyers working from an equipment parts list, OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-20M66FT identifies more than a connector style. It refers here to a 20m (66ft) AOC cable for Generic hosts, supporting 400G operation with OSFP (RHS/Flat Top) to QSFP-DD. The sections below separate the OEM cross-reference, physical specification and HT factory checks for straightforward purchasing review.
OEM Part Number: OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-20M66FTHT Part Number: OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-20M66FT
Product Highlights
- HT-manufactured AOC assembly in 20m (66ft)
- 400G connectivity at 400Gbps
- Interface configuration: OSFP (RHS/Flat Top) to QSFP-DD
- Fixed length and part number: 20m (66ft), OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-20M66FT
- Cable construction: AOC
- Maximum power consumption: 14W (OSFP End)10W (QSFP-DD End)
- Minimum bend radius: 30mm
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-20M66FT |
|---|---|
| Manufacturer | HT |
| Form Factor | OSFP (RHS/Flat Top) to QSFP-DD |
| Max. Data Rate | 400Gbps |
| Cable Length | 20m (66ft) |
| Cable Type | AOC |
| Wavelength | 850nm |
| Minimum Bend Radius | 30mm |
| Transmitter Type | VSCEL |
| Receiver Type | PIN |
| Max. Power Consumption | 14W (OSFP End)10W (QSFP-DD End) |
| Modulation Format | OSFP-4x 100G-PAM4QSFP-DD-8x 50G-PAM4 |
| CDR (Clock and Data Recovery) | No |
| Jacket Material | OFNP |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Protocols | OSFP MSA, QSFP-DD MSA, CMIS 4.0, IEEE 802.3ck-400GAUI-4, IEEE 802.3bs-400GAUI-8 |
Signal and Lane Configuration
The listed modulation format is OSFP-4x 100G-PAM4QSFP-DD-8x 50G-PAM4. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.
Position Within the Length Range
OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-20M66FT occupies the middle of this family between OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-15M49FT at 15m (49ft) and OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-25M82FT at 25m (82ft). It adds 5m over the shorter option for extra routing clearance, while the next longer version adds another 5m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.
Procurement and Port-Mapping Review
A useful purchase order should identify the host platform, the expected OEM code and the exact cable length as separate pieces of information. This prevents a physically similar assembly from being substituted when the port identification or reach is different. For mixed-length installations, prepare one order line per part number and reconcile each delivered cable with its intended pair of ports. For this assembly, the minimum bend radius is 30mm; the stated power consumption is 14W (OSFP End)10W (QSFP-DD End); the jacket material is OFNP.
Power and Thermal Planning
The rated power consumption is 14W (OSFP End)10W (QSFP-DD End). Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.
Cable Construction and Routing
This assembly uses OFNP jacket, minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.
Network and Protocol Considerations
The intended application is determined by the host interface and protocol support. Listed interface and protocol references include OSFP MSA, QSFP-DD MSA, CMIS 4.0, IEEE 802.3ck-400GAUI-4, IEEE 802.3bs-400GAUI-8. Confirm that the host firmware and port configuration support the same operating mode.
Integrated Optical Assembly
The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.
Length Selection and Installation Planning
The 20m (66ft) reach of OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-20M66FT is useful only when the managed pathway requires it; straight-line distance between ports is not a sufficient measurement. Check the route around rack rails, cable managers and maintenance clearances, then protect the integrated optical cable and both optical engines from tight bends and unsupported spans. Within this family, OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-15M49FT is shorter at 15m (49ft), while OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-25M82FT is the next longer choice at 25m (82ft); comparing those two boundaries helps avoid both tension and unnecessary slack.
Generic Compatibility and Factory Testing
Our procurement-oriented compatibility check begins with the OEM reference and ends with a live host link. We record the physical length separately from the identification configuration, so the cable supplied for this page remains the stated version rather than a generic length substitute. The check includes receive activity and diagnostic indications, followed by a final inspection of both ends.
Ordering Information
For a clear bill of materials, quote the OEM reference, HT part number, length and quantity on the same line. Add the switch or server model and software release when a pre-order review is required; project labels can repeat those details for receiving and installation teams. This page’s fixed configuration is 20m (66ft); another length must be quoted under its corresponding part number.
Quality Assurance and Packaging
Before packing, the assembly is checked for connector condition, identification and link operation. Cables for multi-line orders can be labelled and grouped by part number, making it easier to match each length to the procurement record without opening every protective bag. Neutral packaging and customer-specific packing documentation are available on request.
Frequently Asked Questions
Is this an original equipment manufacturer cable?
No. It is manufactured by HT under our own manufacturer identity.
Will any matching connector operate at the same speed?
Not necessarily. Both hosts must support the stated rate, identification, lane mapping and any required breakout configuration; mechanical compatibility alone is insufficient.
What details assist a compatibility review?
Provide the equipment manufacturer, model, port type, hardware revision and software release, together with the OEM reference, required length and quantity.
How should an unused assembly be stored?
Protect both connector ends, keep the cable in a loose bend-safe coil and retain its part-number label so the length and compatibility identity remain traceable.
Shipping and Lead Time
Available stock is generally dispatched within one to three working days after order confirmation, with production lead times advised for larger quantities. International express, air cargo and sea freight can be selected according to destination and carton volume; customer courier accounts and nominated forwarders are also accepted.