Juniper OSFP-SR8-800G Compatible 800G Single-port OSFP IHS/Closed Finned Top SR8 Transceiver Module
This Juniper OSFP-SR8-800G compatible transceiver provides 800G connectivity in a hot-swappable Single-port OSFP IHS/Closed Finned Top package. Its optical design operates at 850nm for up to 60m on OM3 / 100m on OM4, using MTP/MPO-16 APC. Complete parameters and related OEM references help procurement teams match an equipment parts list to a clearly defined optical product.
OEM Part Number: OSFP-SR8-800GHT Part Number: OSFP-SR8-800G
Product Highlights
- Compatible alternative to Juniper OSFP-SR8-800G
- 800G connectivity at 850Gbps (8x 106.25Gbps)
- Optical wavelength: 850nm
- Specified reach: 60m on OM3 / 100m on OM4
- MTP/MPO-16 APC / MMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | OSFP-SR8-800G |
|---|---|
| Manufacturer | HT |
| Form Factor | Single-port OSFP IHS/Closed Finned Top |
| Max. Data Rate | 850Gbps (8x 106.25Gbps) |
| Wavelength | 850nm |
| Max. Cable Distance | 60m@OM3/100m@OM4 |
| Connector | MTP/MPO-16 APC |
| Media | MMF |
| Transmitter Type | VCSEL |
| Receiver Type | PD |
| TX Power | -4.6~4dBm |
| Minimum Receiver Power | -6.4dBm |
| Power Budget | 1.8dB |
| Receiver Overload | 4dBm |
| Max. Power Consumption | 16W |
| Extinction Ratio | ＞2.5dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 8x100G-PAM4 |
| Modulation (Optical) | 8x100G-PAM4 |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Inbuilt FEC | Yes |
| Protocols | OSFP MSA Rev 5.1, CMIS Rev 5.0, IEEE 802.3df-2024, IEEE 802.3df-2024 |
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The MTP/MPO-16 APC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 800G interface configuration must match the remote equipment; sharing a Single-port OSFP IHS/Closed Finned Top housing alone does not make two transceiver types interoperable.
For this multimode module, confirm fiber grade, modal bandwidth and total loss before commissioning. The 60m on OM3 / 100m on OM4 figure applies only under suitable cabling conditions. Inspect every MTP/MPO-16 APC mating point and match the remote optical standard.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -4.6~4dBm; the stated optical power budget is 1.8dB. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Procurement and Asset Identification
A useful purchase order identifies the host platform, expected OEM code and optical standard separately. This prevents a module with the same housing but another wavelength, reach or identification profile from being substituted. For mixed deployments, keep one order line per OEM reference and reconcile each received unit with its intended port. For this model, the principal parameters are data rate 850Gbps (8x 106.25Gbps), wavelength 850nm, rated reach 60m on OM3 / 100m on OM4.
Juniper Compatibility and Factory Testing
Compatibility testing for OSFP-SR8-800G combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Ordering Information
Use OSFP-SR8-800G as the compatibility cross-reference and OSFP-SR8-800G as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Quality Assurance and Packaging
Each OSFP-SR8-800G compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Juniper transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies OSFP-SR8-800G, not an original Juniper-branded module.
Which fiber and connector are required?
Use MTP/MPO-16 APC with MMF. The specified maximum reach is 60m on OM3 / 100m on OM4, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.