Juniper Networks Part Number Compatible 100G QSFP28 4WDM-20 Transceiver Module
This Juniper Networks Part Number compatible transceiver provides 100G connectivity in a hot-swappable QSFP28 package. Its optical design operates at 1310nm for up to 20km, using Duplex LC. Complete parameters and related OEM references help procurement teams match an equipment parts list to a clearly defined optical product.
OEM Part Number: Part NumberHT Part Number: QSFP-4W20-100G-I
Product Highlights
- Compatible alternative to Juniper Networks Part Number
- 100G connectivity at 103.125Gbps (4x 25.78Gbps)
- Optical wavelength: 1310nm
- Specified reach: 20km
- Duplex LC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: -40 to 85°C (-40 to 185°F)
Specifications
| Juniper Networks Compatible | Part Number |
|---|---|
| Manufacturer | HT |
| HT Part Number | QSFP-4W20-100G-I |
| Form Factor | QSFP28 |
| Max Data Rate | 103.125Gbps (4x 25.78Gbps) |
| Wavelength | 1310nm |
| Max Cable Distance | 20km |
| Connector | Duplex LC |
| Media | SMF |
| Transmitter Type | EML |
| Receiver Type | PIN |
| TX Power | -4.3~4.5dBm |
| RX Power | -14.5~4.5dBm |
| Power Budget | 10.2db |
| Extinction Ratio | ＞4dB |
| Power Consumption | <4.5W |
| DDM/DOM | Supported |
| Modulation (Electrical) | 4x 25G-NRZ |
| Modulation (Optical) | 4x 25G-NRZ |
| Packaging Technology | COB (chip on board) Packaging |
| Industrial Temperature Range | -40 to 85°C (-40 to 185°F) |
| Protocols | QSFP28 MSA,IEEE 802.3-2018,4WDM-20,SFF-8661,SFF-8636 |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
The industrial temperature rating makes this version appropriate for controlled outdoor cabinets, transport nodes and other installations exposed to wider ambient temperature variation. Adequate airflow, protected cable routing and host-platform temperature limits still apply.
Before commissioning, measure the complete single-mode channel against the stated budget for 20km. Inspect every Duplex LC connection and record diagnostic power where supported. Both ends must agree on rate, wavelength and optical standard.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -4.3~4.5dBm; the stated optical power budget is 10.2db. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Procurement and Asset Identification
A useful purchase order identifies the host platform, expected OEM code and optical standard separately. This prevents a module with the same housing but another wavelength, reach or identification profile from being substituted. For mixed deployments, keep one order line per OEM reference and reconcile each received unit with its intended port. For this model, the principal parameters are data rate 103.125Gbps (4x 25.78Gbps), wavelength 1310nm, rated reach 20km.
Juniper Networks Compatibility and Factory Testing
Factory verification starts with the expected Part Number identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Ordering Information
Quote HT part number QSFP-4W20-100G-I together with OEM reference Part Number and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Juniper Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies Part Number, not an original Juniper Networks-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 20km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.