QDD-200G-8LCAO01-E-3M10FT 200G QSFP-DD 8 x 25G NRZ to 8 x 25G LC Duplex Active Optical Breakout Cable, 3m (10ft)
The QDD-200G-8LCAO01-E-3M10FT compatible assembly is intended for Generic equipment that requires a 200G direct-attached connection. This version is specifically 3m (10ft), with QSFP28-DD to Duplex-LC and its own order reference. Exact length pages and equivalent brand references are linked to make multi-product procurement easier to verify.
OEM Part Number: QDD-200G-8LCAO01-E-3M10FTHT Part Number: QDD-200G-8LCAO01-E-3M10FT
Product Highlights
- HT-manufactured AOC assembly in 3m (10ft)
- 200G connectivity at 200Gbps
- Interface configuration: QSFP28-DD to Duplex-LC
- Fixed length and part number: 3m (10ft), QDD-200G-8LCAO01-E-3M10FT
- Cable construction: Optical Cable
- Maximum power consumption: ≤3.47W
- Minimum bend radius: 30mm
Specifications
| HT Part Number | QDD-200G-8LCAO01-E-3M10FT |
|---|---|
| Manufacturer | HT |
| Connector Type | QSFP28-DD to Duplex-LC |
| Max Data Rate | 200Gbps |
| Minimum Bend Radius | 30mm |
| Cable Length | 3m (10ft) |
| Wavelength | 850nm |
| Cable Type | Optical Cable |
| Modulation Format | NRZ |
| Power Consumption | ≤3.47W |
| Power supply | 3.5V |
| Extend Temperature Range | -20°C to +85°C |
| Protocols | QSFP-DD MSA CMIS 4.0, IEEE 802.3bs 200G-SR8, IEEE 802.3by 25G-SR |
| Application | Ethernet, 5G Front Haul |
Signal and Lane Configuration
The listed modulation format is NRZ. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.
Breakout Port Mapping
The QSFP28-DD to Duplex-LC configuration divides the high-speed interface into multiple lower-speed connections. Verify the upstream lane assignment, downstream port speeds and breakout setting on the host before connecting the assembly. Each branch must attach to the correct remote interface.
Integrated Optical Assembly
The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.
Length Selection and Installation Planning
At 3m (10ft), this assembly can bridge non-aligned ports or adjacent racks while remaining a single direct-attach link. Support longer horizontal runs with suitable cable management and preserve space for cooling and future maintenance.
Position Within the Length Range
QDD-200G-8LCAO01-E-3M10FT occupies the middle of this family between QDD-200G-8LCAO01-E-1M3FT at 1m (3ft) and QSFP28-DD to Duplex-LC-200G-AOC-5M16FT at 5m (16ft). It adds 2m over the shorter option for extra routing clearance, while the next longer version adds another 2m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.
Procurement and Port-Mapping Review
A useful purchase order should identify the host platform, the expected OEM code and the exact cable length as separate pieces of information. This prevents a physically similar assembly from being substituted when the port identification or reach is different. For mixed-length installations, prepare one order line per part number and reconcile each delivered cable with its intended pair of ports. For this assembly, the minimum bend radius is 30mm; the stated power consumption is ≤3.47W.
Power and Thermal Planning
The rated power consumption is ≤3.47W. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.
Cable Construction and Routing
This assembly uses minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.
Network and Protocol Considerations
The intended application is Ethernet, 5G Front Haul. Listed interface and protocol references include QSFP-DD MSA CMIS 4.0, IEEE 802.3bs 200G-SR8, IEEE 802.3by 25G-SR. Confirm that the host firmware and port configuration support the same operating mode.
Generic Compatibility and Factory Testing
Our procurement-oriented compatibility check begins with the OEM reference and ends with a live host link. We record the physical length separately from the identification configuration, so the cable supplied for this page remains the stated version rather than a generic length substitute. Where supported by the host, receive activity and diagnostic indications are reviewed together with the established link.
Ordering Information
For a clear bill of materials, quote the OEM reference, HT part number, length and quantity on the same line. Add the switch or server model and software release when a pre-order review is required; project labels can repeat those details for receiving and installation teams. Keep QDD-200G-8LCAO01-E-3M10FT associated with 3m (10ft) throughout the order and receiving record.
Quality Assurance and Packaging
Before packing, the assembly is checked for connector condition, identification and link operation. Cables for multi-line orders can be labelled and grouped by part number, making it easier to match each length to the procurement record without opening every protective bag. Volume orders can include customer references on the labels and carton list.
Frequently Asked Questions
Is this an original equipment manufacturer cable?
No. It is manufactured by HT under our own manufacturer identity.
How should an unused assembly be stored?
Protect both connector ends, keep the cable in a loose bend-safe coil and retain its part-number label so the length and compatibility identity remain traceable.
Can different brands be connected with the same assembly?
Only where both hosts explicitly support the complete interface and compatibility arrangement. Document each end and select the appropriate brand-specific product when required.
Does this order code cover multiple lengths?
No. QDD-200G-8LCAO01-E-3M10FT refers here to 3m (10ft). Every other verified length has a separate part number and page in the length list.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, while production quantities are confirmed with the order. International express, air cargo and sea freight can be selected according to destination and carton volume; customer courier accounts and nominated forwarders are also accepted.