Juniper Networks QDD-400G-ER4-30 Compatible 400G QSFP-DD ER4L Transceiver Module
Built for hosts recognizing QDD-400G-ER4-30, this HT-manufactured QSFP-DD module delivers 400G transmission at 1310nm. Its rated reach is 30km, with Duplex LC/UPC as the physical interface. The specifications and engineering guidance below support procurement teams match an equipment parts list to a clearly defined optical product, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: QDD-400G-ER4-30HT Part Number: QDD-ER4L-400G
Product Highlights
- Compatible alternative to Juniper Networks QDD-400G-ER4-30
- 400G connectivity at 400Gbps
- Optical wavelength: 1310nm
- Specified reach: 30km
- Duplex LC/UPC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | QDD-ER4L-400G |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP-DD |
| Max. Data Rate | 400Gbps |
| Wavelength | 1310nm |
| Max. Cable Distance | 30km |
| Connector | Duplex LC/UPC |
| Media | SMF |
| Transmitter Type | EML |
| Receiver Type | APD |
| TX Power | 0.4~6.5dBm |
| Minimum Receiver Power | -10.1dBm |
| Power Budget | 10.5dB |
| Receiver Overload | -3.4dB |
| Max Power Consumption | 12W |
| Extinction Ratio | 6dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 8x53.125G-PAM4 |
| Modulation (Optical) | 4x106.25G-PAM4 |
| DSP | TX and RX |
| Inbuilt FEC | No |
| Bit Error Ratio (BER) | 2.4E-4 |
| MTBF | 2050000 Hours (@40°C, 60% CL)818000 Hours (@40°C, 90% CL)1300000 Hours (@55°C, 60% CL)519000 Hours (@55°C, 90% CL) |
| Packaging Technology | BOX |
| Application | Data Center, Enterprise Networking, 400G Ethernet |
| Protocols | QSFP-DD MSA, CMIS Rev4.0, IEEE 802.3, IEEE 802.3bs, OIF 56G PAM4 |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 400G interface configuration must match the remote equipment; sharing a QSFP-DD housing alone does not make two transceiver types interoperable.
Before commissioning, measure the complete single-mode channel against the stated budget for 30km. Inspect every Duplex LC/UPC connection and record diagnostic power where supported. Both ends must agree on rate, wavelength and optical standard.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is 0.4~6.5dBm; the stated optical power budget is 10.5dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Procurement and Asset Identification
A useful purchase order identifies the host platform, expected OEM code and optical standard separately. This prevents a module with the same housing but another wavelength, reach or identification profile from being substituted. For mixed deployments, keep one order line per OEM reference and reconcile each received unit with its intended port. For this model, the principal parameters are data rate 400Gbps, wavelength 1310nm, rated reach 30km.
Juniper Networks Compatibility and Factory Testing
The module is checked for host recognition as QDD-400G-ER4-30, link establishment and diagnostic reporting. Physical cage fit alone is not treated as evidence of compatibility. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Ordering Information
Quote HT part number QDD-ER4L-400G together with OEM reference QDD-400G-ER4-30 and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Juniper Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QDD-400G-ER4-30, not an original Juniper Networks-branded module.
Which fiber and connector are required?
Use Duplex LC/UPC with SMF. The specified maximum reach is 30km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.