Broadcom QDD-XDR4-400G Compatible 400G QSFP-DD XDR4 Transceiver Module
Built for hosts recognizing QDD-XDR4-400G, this HT-manufactured QSFP-DD module delivers 400G transmission at 1310nm. Its rated reach is 2km, with MPO-12/APC as the physical interface. The specifications and engineering guidance below support procurement teams match an equipment parts list to a clearly defined optical product, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: QDD-XDR4-400GHT Part Number: QDD-XDR4-400G
Product Highlights
- Compatible alternative to Broadcom QDD-XDR4-400G
- 400G connectivity at 400Gbps
- Optical wavelength: 1310nm
- Specified reach: 2km
- MPO-12/APC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | QDD-XDR4-400G |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP-DD |
| Max. Data Rate | 400Gbps |
| Wavelength | 1310nm |
| Max. Cable Distance | 2km |
| Connector | MPO-12/APC |
| Media | SMF |
| Transmitter Type | 1310nm EML |
| Receiver Type | PIN |
| TX Power | -3.1~4dBm |
| Minimum Receiver Power | -7.1dBm |
| Power Budget | 4dB |
| Receiver Overload | 4dBm |
| Max. Power Consumption | 9W |
| Extinction Ratio | 3.5dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 8x50G-PAM4 |
| Modulation (Optical) | 4x100G-PAM4 |
| DSP | TX and RX |
| Inbuilt FEC | No |
| Core Size | G.652/9um |
| Packaging Technology | COB (Chip on Board) Packaging |
| Protocols | QSFP-DD MSA, CMIS.5.0, IEEE 802.3bs |
Applications and Optical Link Design
This coherent interface is suited to data-center interconnect, metro transport and managed DWDM links where the host platform supports the stated modulation and FEC modes. Design the optical line around the actual launch power, receiver range, OSNR requirement and span loss; the stated reach is not a substitute for a link-budget calculation. Use matching coherent modules and the appropriate DWDM channel plan at both ends.
Before deployment, check the host port type, supported data rate and firmware requirements. The 400G interface configuration must match the remote equipment; sharing a QSFP-DD housing alone does not make two transceiver types interoperable.
For this coherent interface, document the wavelength plan and modulation or FEC settings before commissioning. Measure span loss and verify adequate OSNR. Interoperability depends on compatible coherent modes as well as form factor, so another coherent part number must not be substituted without engineering review.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -3.1~4dBm; the stated optical power budget is 4dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Procurement and Asset Identification
A useful purchase order identifies the host platform, expected OEM code and optical standard separately. This prevents a module with the same housing but another wavelength, reach or identification profile from being substituted. For mixed deployments, keep one order line per OEM reference and reconcile each received unit with its intended port. For this model, the principal parameters are data rate 400Gbps, wavelength 1310nm, rated reach 2km.
Broadcom Compatibility and Factory Testing
Compatibility testing for QDD-XDR4-400G combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Ordering Information
Use QDD-XDR4-400G as the compatibility cross-reference and QDD-XDR4-400G as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Quality Assurance and Packaging
Each QDD-XDR4-400G compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Broadcom transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QDD-XDR4-400G, not an original Broadcom-branded module.
Which fiber and connector are required?
Use MPO-12/APC with SMF. The specified maximum reach is 2km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.