Generic QDD-ZR-400G Compatible 400G QSFP-DD Transceiver Module
Built for hosts recognizing QDD-ZR-400G, this HT-manufactured QSFP-DD module delivers 400G transmission at 1528.77~1566.52nm. Its rated reach is Amplified: ≤120km Unamplified：≤40km, with Duplex LC/UPC as the physical interface. The specifications and engineering guidance below support procurement teams match an equipment parts list to a clearly defined optical product, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: QDD-ZR-400GHT Part Number: QDD-ZR-400G
Product Highlights
- Compatible alternative to Generic QDD-ZR-400G
- 400G connectivity at 400Gbps
- Optical wavelength: 1528.77~1566.52nm
- Specified reach: Amplified: ≤120km Unamplified：≤40km
- Duplex LC/UPC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0℃ to 70°C(32 to 158°F)
Specifications
| HT Part Number | QDD-ZR-400G |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP-DD |
| Max. Data Rate | 400Gbps |
| Wavelength | 1528.77~1566.52nm |
| Max. Cable Distance | Amplified: ≤120km Unamplified：≤40km |
| Connector | Duplex LC/UPC |
| Media | SMF |
| CD Robustness | 2400(ps/nm) |
| DDM/DOM | Supported |
| TX Power | -13~-9dBm |
| RX Power | Amplified: Full Rx OSNR tolerance: -12~0dBm Extended range: -15~1dBm Unamplified: -20~0dBm |
| Max. Power Consumption | 18.5W |
| Minimum Receiver Power | Amplified: -12dBm Unamplified: ≤-20dBm |
| OSNR Tolerance | 26dB/0.1nm |
| Commercial Temperature Range | 0℃ to 70°C(32 to 158°F) |
| Inbuilt FEC | CFEC |
| Modulation Format | DP-16QAM |
| Protocols | OIF 400ZR, OIF-CMIS-05.2, OIF-C-CMIS-01.2, QSFP-DD-Hardware-Rev6.3, IEEE Std 802.3-2018 |
| Application | Edge DCI |
Applications and Optical Link Design
This coherent interface is suited to data-center interconnect, metro transport and managed DWDM links where the host platform supports the stated modulation and FEC modes. Design the optical line around the actual launch power, receiver range, OSNR requirement and span loss; the stated reach is not a substitute for a link-budget calculation. Use matching coherent modules and the appropriate DWDM channel plan at both ends.
Before deployment, check the host port type, supported data rate and firmware requirements. The 400G interface configuration must match the remote equipment; sharing a QSFP-DD housing alone does not make two transceiver types interoperable.
Coherent deployment requires a line-system review, not merely a matching connector. Confirm the DWDM channel, launch-power range, receiver limits, OSNR and FEC mode at both ends. Span loss and amplifier operation must remain inside the supported envelope, and stated reach should be validated against the actual route.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -13~-9dBm. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Procurement and Asset Identification
A useful purchase order identifies the host platform, expected OEM code and optical standard separately. This prevents a module with the same housing but another wavelength, reach or identification profile from being substituted. For mixed deployments, keep one order line per OEM reference and reconcile each received unit with its intended port. For this model, the principal parameters are data rate 400Gbps, wavelength 1528.77~1566.52nm, rated reach Amplified: ≤120km Unamplified：≤40km.
Generic Compatibility and Factory Testing
Factory verification starts with the expected QDD-ZR-400G identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Ordering Information
Use QDD-ZR-400G as the compatibility cross-reference and QDD-ZR-400G as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Quality Assurance and Packaging
Each QDD-ZR-400G compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original equipment manufacturer transceiver?
No. It is an HT-manufactured compatible transceiver supplied under our own manufacturer identity, not an original equipment manufacturer module.
Which fiber and connector are required?
Use Duplex LC/UPC with SMF. The specified maximum reach is Amplified: ≤120km Unamplified：≤40km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.