Cisco QSFP-100G-AOC10M Compatible 100G QSFP28 4 x 25G NRZ Active Optical Cable, 10m (33ft)
The QSFP-100G-AOC10M compatible assembly is intended for Cisco equipment that requires a 100G direct-attached connection. This version is specifically 10m (33ft), with QSFP28 to QSFP28 and its own order reference. Exact length pages and equivalent brand references are linked to make multi-product procurement easier to verify.
OEM Part Number: QSFP-100G-AOC10MHT Part Number: QSFP-100G-AOC10M
Product Highlights
- Compatible alternative to Cisco QSFP-100G-AOC10M
- 100G connectivity at 100Gbps
- Interface configuration: QSFP28 to QSFP28
- Fixed length and part number: 10m (33ft), QSFP-100G-AOC10M
- Cable construction: Optical Cable
- Maximum power consumption: <2.2W
- Minimum bend radius: 30mm
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | QSFP-100G-AOC10M |
|---|---|
| Cisco Compatible | QSFP-100G-AOC10M |
| Manufacturer | HT |
| Form Factor | QSFP28 to QSFP28 |
| Max Data Rate | 100Gbps |
| Minimum Bend Radius | 30mm |
| Cable Length | 10m (32.81ft) |
| Jacket Material | OFNP |
| Cable Type | Optical Cable |
| Receiver Type | PIN |
| Transmitter Type | VSCEL |
| Wavelength | 850nm |
| Power Consumption | <2.2W |
| MTBF | ≈50 Million Hours |
| Power supply | 3.3V |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Protocols | IEEE 802.3 bm, SFF-8665 |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Modulation Format | 4x 25G-NRZ to 4x 25G-NRZ |
| Application | 100G Ethernet |
Cisco OEM Reference
Cisco describes its QSFP-100G-AOCxM family as active optical cable for short connections within and across racks. Compared with copper direct attach, the thinner and lighter optical assembly can simplify cable management and support efficient airflow in high-density racks. Select this HT compatible version by the exact length and OEM part number.
Network and Protocol Considerations
The intended application is 100G Ethernet. Listed interface and protocol references include IEEE 802.3 bm, SFF-8665. Confirm that the host firmware and port configuration support the same operating mode.
Integrated Optical Assembly
The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.
Length Selection and Installation Planning
Longer assemblies require disciplined cable dressing. For QSFP-100G-AOC10M at 10m (33ft), use the intended managers rather than a diagonal route across the rack, and leave enough space to release each connector. Any service allowance should be loose and supported, with the integrated optical cable and both optical engines protected throughout the path. Within this family, QSFP-100G-AOC7M is shorter at 7m (23ft), while QSFP-100G-AOC15M is the next longer choice at 15m (49ft); comparing those two boundaries helps avoid both tension and unnecessary slack.
Position Within the Length Range
QSFP-100G-AOC10M occupies the middle of this family between QSFP-100G-AOC7M at 7m (23ft) and QSFP-100G-AOC15M at 15m (49ft). It adds 3m over the shorter option for extra routing clearance, while the next longer version adds another 5m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.
Procurement and Port-Mapping Review
A useful purchase order should identify the host platform, the expected OEM code and the exact cable length as separate pieces of information. This prevents a physically similar assembly from being substituted when the port identification or reach is different. For mixed-length installations, prepare one order line per part number and reconcile each delivered cable with its intended pair of ports. For this assembly, the minimum bend radius is 30mm; the stated power consumption is <2.2W; the jacket material is OFNP.
Signal and Lane Configuration
The listed modulation format is 4x 25G-NRZ to 4x 25G-NRZ. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.
Power and Thermal Planning
The rated power consumption is <2.2W. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.
Cable Construction and Routing
This assembly uses OFNP jacket, minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.
Cisco Compatibility and Factory Testing
Our procurement-oriented compatibility check begins with the OEM reference and ends with a live host link. We record the physical length separately from the identification configuration, so the cable supplied for this page remains the stated version rather than a generic length substitute. The check includes receive activity and diagnostic indications, followed by a final inspection of both ends.
Ordering Information
For a clear bill of materials, quote the OEM reference, HT part number, length and quantity on the same line. Add the switch or server model and software release when a pre-order review is required; project labels can repeat those details for receiving and installation teams. This page’s fixed configuration is 10m (33ft); another length must be quoted under its corresponding part number.
Quality Assurance and Packaging
Before packing, the assembly is checked for connector condition, identification and link operation. Cables for multi-line orders can be labelled and grouped by part number, making it easier to match each length to the procurement record without opening every protective bag. Standard protective packing is used by default, with project documentation arranged when requested.
Frequently Asked Questions
Is this an original Cisco cable?
No. It is an HT-manufactured compatible alternative for equipment that specifies Cisco QSFP-100G-AOC10M.
Does this order code cover multiple lengths?
No. QSFP-100G-AOC10M refers here to 10m (33ft). Every other verified length has a separate part number and page in the length list.
Are separate transceivers or patch leads required?
No. This is one complete direct-attach assembly. The ends are not detachable modules and should not be separated from the cable.
Can excess cable be folded into a compact bundle?
No. Use a supported, bend-safe service loop and observe the listed minimum bend radius. Do not crease the cable or tighten ties around the connector boots.
Shipping and Lead Time
Available stock is generally dispatched within one to three working days after order confirmation, with production lead times advised for larger quantities. Worldwide courier services are available, with air or sea freight for consolidated shipments; freight-collect delivery and coordination with a customer’s logistics provider can be arranged.