Generic QSFP-BX30-100G Compatible 100G QSFP28 BX30-D Transceiver Module 30km 1309.14nm-Tx/1304.58nm-Rx
Built for hosts recognizing QSFP-BX30-100G, this HT-manufactured QSFP28 module delivers 100G transmission at 1309.14nm-Tx/1304.58nm-Rx. Its rated reach is 30km, with Simplex LC as the physical interface. The specifications and engineering guidance below support procurement teams match an equipment parts list to a clearly defined optical product, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: QSFP-BX30-100GHT Part Number: QSFP-BX30-100G
Product Highlights
- Compatible alternative to Generic QSFP-BX30-100G
- 100G connectivity at 106.25Gbps
- Optical wavelength: 1309.14nm-Tx/1304.58nm-Rx
- Specified reach: 30km
- Simplex LC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | QSFP-BX30-100G |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP28 |
| Max Data Rate | 106.25Gbps |
| Wavelength | 1309.14nm-Tx/1304.58nm-Rx |
| Max Cable Distance | 30km |
| Connector | Simplex LC |
| Media | SMF |
| Transmitter Type | EML |
| Receiver Type | APD |
| TX Power | 0~5.6dBm |
| Receiver Sensitivity | -14.7dBm |
| Min Power Budget | 14.7dB |
| Receiver Overload | -3.4dBm |
| Power Consumption | <4.5W |
| Extinction Ratio | ＞5dB |
| DDM/DOM | Supported |
| Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 4x 25G-NRZ |
| Modulation (Optical) | 1x 100G-PAM4 |
| Protocols | IEEE 802.3bs, 100G Lambda MSA |
Applications and Optical Link Design
This BiDi interface is useful where only one fiber strand is available between two sites or racks. It must be paired with the complementary wavelength direction: one end transmits on the wavelength that the other end receives. Verify the paired part number, connector polish and fiber plant before installation, and measure link loss against the specified optical budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a QSFP28 housing alone does not make two transceiver types interoperable.
BiDi operation saves a fiber strand but makes wavelength orientation critical. Record the part installed at each end and check its paired receive wavelength. The 30km rating still depends on total channel loss, including connectors and splices.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is 0~5.6dBm; receiver sensitivity is -14.7dBm. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Procurement and Asset Identification
A useful purchase order identifies the host platform, expected OEM code and optical standard separately. This prevents a module with the same housing but another wavelength, reach or identification profile from being substituted. For mixed deployments, keep one order line per OEM reference and reconcile each received unit with its intended port. For this model, the principal parameters are data rate 106.25Gbps, wavelength 1309.14nm-Tx/1304.58nm-Rx, rated reach 30km.
Generic Compatibility and Factory Testing
Compatibility testing for QSFP-BX30-100G combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Ordering Information
Use QSFP-BX30-100G as the compatibility cross-reference and QSFP-BX30-100G as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Quality Assurance and Packaging
Each QSFP-BX30-100G compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original equipment manufacturer transceiver?
No. It is an HT-manufactured compatible transceiver supplied under our own manufacturer identity, not an original equipment manufacturer module.
Which fiber and connector are required?
Use Simplex LC with SMF. The specified maximum reach is 30km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.