Cisco QSFP-BX40-100G Compatible 100G QSFP28 BX40-U Transceiver Module 40km on OS2 1304.58nm-TX/1309.14nm-RX
Built for hosts recognizing QSFP-BX40-100G, this HT-manufactured QSFP28 module delivers 100G transmission at 1304.58nm-TX/1309.14nm-RX. Its rated reach is 40km on OS2, with Simplex LC/UPC as the physical interface. The specifications and engineering guidance below support procurement teams match an equipment parts list to a clearly defined optical product, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: QSFP-BX40-100GHT Part Number: QSFP-BX40-100G
Product Highlights
- Compatible alternative to Cisco QSFP-BX40-100G
- 100G connectivity at 106.25Gbps
- Optical wavelength: 1304.58nm-TX/1309.14nm-RX
- Specified reach: 40km on OS2
- Simplex LC/UPC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | QSFP-BX40-100G |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP28 |
| Max. Data Rate | 106.25Gbps |
| Wavelength | 1304.58nm-TX/1309.14nm-RX |
| Max. Cable Distance | 40km@OS2 |
| Connector | Simplex LC/UPC |
| Media | SMF |
| Transmitter Type | MZM EML |
| Receiver Type | APD |
| TX Power | 1.7~7.1dBm |
| Minimum Receiver Power | -16dBm |
| Power Budget | 17.7dB |
| Receiver Overload | -3dBm |
| Max. Power Consumption | 4.5W |
| Extinction Ratio | > 5.0dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 4x 25G-NRZ |
| Modulation (Optical) | 1x 100G-PAM4 |
| Inbuilt FEC | KP4 |
| Bit Error Ratio (BER) | 2E-4 |
| Protocols | QSFP28 MSA, IEEE 802.3bs, 100G Lambda MSA |
Applications and Optical Link Design
This BiDi interface is useful where only one fiber strand is available between two sites or racks. It must be paired with the complementary wavelength direction: one end transmits on the wavelength that the other end receives. Verify the paired part number, connector polish and fiber plant before installation, and measure link loss against the specified optical budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a QSFP28 housing alone does not make two transceiver types interoperable.
This single-fiber interface must be paired with the complementary wavelength direction. One end transmits on the wavelength the other receives. Verify connector polish and measure loss over the 40km on OS2 design range before service.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is 1.7~7.1dBm; the stated optical power budget is 17.7dB. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Procurement and Asset Identification
A useful purchase order identifies the host platform, expected OEM code and optical standard separately. This prevents a module with the same housing but another wavelength, reach or identification profile from being substituted. For mixed deployments, keep one order line per OEM reference and reconcile each received unit with its intended port. For this model, the principal parameters are data rate 106.25Gbps, wavelength 1304.58nm-TX/1309.14nm-RX, rated reach 40km on OS2.
Cisco Compatibility and Factory Testing
Compatibility testing for QSFP-BX40-100G combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Ordering Information
Quote HT part number QSFP-BX40-100G together with OEM reference QSFP-BX40-100G and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Quality Assurance and Packaging
Quality control covers the optical or electrical interface, host identification and operating link. The verified unit is then individually protected and cartoned. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Cisco transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QSFP-BX40-100G, not an original Cisco-branded module.
Which fiber and connector are required?
Use Simplex LC/UPC with SMF. The specified maximum reach is 40km on OS2, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.