QSFP-DD to 8x 25G SFP28-200G-AOC-3M10FT 200G QSFP-DD 8 x 25G NRZ to 8 x 25G SFP28 25G NRZ Active Optical Breakout Cable, 3m (10ft)
The QSFP-DD to 8x 25G SFP28-200G-AOC-3M10FT compatible assembly is intended for Generic equipment that requires a 200G direct-attached connection. This version is specifically 3m (10ft), with QSFP-DD to 8x 25G SFP28 and its own order reference. Exact length pages and equivalent brand references are linked to make multi-product procurement easier to verify.
OEM Part Number: QSFP-DD to 8x 25G SFP28-200G-AOC-3M10FTHT Part Number: QSFP-DD to 8x 25G SFP28-200G-AOC-3M10FT
Product Highlights
- HT-manufactured AOC assembly in 3m (10ft)
- 200G connectivity at 206.24Gbps (8x 25.78Gbps)
- Interface configuration: QSFP-DD to 8x 25G SFP28
- Fixed length and part number: 3m (10ft), QSFP-DD to 8x 25G SFP28-200G-AOC-3M10FT
- Cable construction: OM3
- Maximum power consumption: QSFP-DD <4W,SFP28 <1W
- Minimum bend radius: 30mm
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | QSFP-DD to 8x 25G SFP28-200G-AOC-3M10FT |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP-DD to 8x 25G SFP28 |
| Max. Data Rate | 206.24Gbps (8x 25.78Gbps) |
| Cable Length | 3m |
| Cable Type | OM3 |
| Minimum Bend Radius | 30mm |
| Power Consumption | QSFP-DD <4W,SFP28 <1W |
| Transmitter Type | VSCEL |
| Receiver Type | PIN |
| Modulation Format | NRZ |
| BER | 5E-5 |
| Inbuilt FEC | No |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Protocols | QSFP-DD MSA V5.0,SFP28 MSA,CMIS V4.0,SFF-8472 |
Signal and Lane Configuration
The listed modulation format is NRZ. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.
Breakout Port Mapping
The QSFP-DD to 8x 25G SFP28 configuration divides the high-speed interface into multiple lower-speed connections. Verify the upstream lane assignment, downstream port speeds and breakout setting on the host before connecting the assembly. Each branch must attach to the correct remote interface.
Integrated Optical Assembly
The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.
Length Selection and Installation Planning
At 3m (10ft), this assembly can bridge non-aligned ports or adjacent racks while remaining a single direct-attach link. Support longer horizontal runs with suitable cable management and preserve space for cooling and future maintenance.
Position Within the Length Range
QSFP-DD to 8x 25G SFP28-200G-AOC-3M10FT occupies the middle of this family between QSFP-DD to 8x 25G SFP28-200G-AOC-2M7FT at 2m (7ft) and QSFP-DD to 8x 25G SFP28-200G-AOC-5M16FT at 5m (16ft). It adds 1m over the shorter option for extra routing clearance, while the next longer version adds another 2m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.
Procurement and Port-Mapping Review
A useful purchase order should identify the host platform, the expected OEM code and the exact cable length as separate pieces of information. This prevents a physically similar assembly from being substituted when the port identification or reach is different. For mixed-length installations, prepare one order line per part number and reconcile each delivered cable with its intended pair of ports. For this assembly, the minimum bend radius is 30mm; the stated power consumption is QSFP-DD <4W,SFP28 <1W.
Power and Thermal Planning
The rated power consumption is QSFP-DD <4W,SFP28 <1W. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.
Cable Construction and Routing
This assembly uses minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.
Network and Protocol Considerations
The intended application is determined by the host interface and protocol support. Listed interface and protocol references include QSFP-DD MSA V5.0,SFP28 MSA,CMIS V4.0,SFF-8472. Confirm that the host firmware and port configuration support the same operating mode.
Generic Compatibility and Factory Testing
Our procurement-oriented compatibility check begins with the OEM reference and ends with a live host link. We record the physical length separately from the identification configuration, so the cable supplied for this page remains the stated version rather than a generic length substitute. Both connectors are examined before the operating test, which includes receive activity and diagnostic indications.
Ordering Information
For a clear bill of materials, quote the OEM reference, HT part number, length and quantity on the same line. Add the switch or server model and software release when a pre-order review is required; project labels can repeat those details for receiving and installation teams. This page’s fixed configuration is 3m (10ft); another length must be quoted under its corresponding part number.
Quality Assurance and Packaging
Before packing, the assembly is checked for connector condition, identification and link operation. Cables for multi-line orders can be labelled and grouped by part number, making it easier to match each length to the procurement record without opening every protective bag. Standard protective packing is used by default, with project documentation arranged when requested.
Frequently Asked Questions
Is this an original equipment manufacturer cable?
No. It is manufactured by HT under our own manufacturer identity.
Does this order code cover multiple lengths?
No. QSFP-DD to 8x 25G SFP28-200G-AOC-3M10FT refers here to 3m (10ft). Every other verified length has a separate part number and page in the length list.
Are separate transceivers or patch leads required?
No. This is one complete direct-attach assembly. The ends are not detachable modules and should not be separated from the cable.
Can excess cable be folded into a compact bundle?
No. Use a supported, bend-safe service loop and observe the listed minimum bend radius. Do not crease the cable or tighten ties around the connector boots.
Shipping and Lead Time
Available stock is generally dispatched within one to three working days after order confirmation, with production lead times advised for larger quantities. Worldwide courier services are available, with air or sea freight for consolidated shipments; freight-collect delivery and coordination with a customer’s logistics provider can be arranged.