Extreme QSFP-ELR4-40G Compatible 40G QSFP+ ELR4 Transceiver Module
The QSFP-ELR4-40G compatible module serves equipment requiring a 40G QSFP+ interface with 1310nm optics and a 20km rating. Connection is through Duplex LC. Product data, application guidance and factory verification are presented together to support procurement teams match an equipment parts list to a clearly defined optical product.
OEM Part Number: QSFP-ELR4-40GHT Part Number: QSFP-ELR4-40G
Product Highlights
- Compatible alternative to Extreme QSFP-ELR4-40G
- 40G connectivity at 41.2Gbps (4x 10.3Gbps)
- Optical wavelength: 1310nm
- Specified reach: 20km
- Duplex LC / SMF interface
- Operating temperature: 0 to 70°C(32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| HT Part Number | QSFP-ELR4-40G |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP+ |
| Max. Data Rate | 41.2Gbps (4x 10.3Gbps) |
| Wavelength | 1310nm |
| Max. Transmission Distance | 20km |
| Connector | Duplex LC |
| Media | SMF |
| Transimitter Type | DFB CWDM |
| Receiver Type | PIN |
| TX Power | -4.5~2.3dBm |
| Receiver Sensitivity | <-12.5dBm |
| Power Budget | 8dB |
| Receiver Overload | 3.3dBm |
| Max. Power Consumption | ≤3.5W |
| Extinction Ratio | >3.5dB |
| Operating Temperature | 0 to 70°C(32 to 158°F) |
| Protocols | QSFP+ MSA, SFF-8436 |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 40G interface configuration must match the remote equipment; sharing a QSFP+ housing alone does not make two transceiver types interoperable.
The single-mode link budget should include fiber attenuation, connectors, splices and panels over the intended 20km route. Keep the Duplex LC interface clean and match the remote optical standard. Consider receiver overload as well as insufficient power on short links.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -4.5~2.3dBm; receiver sensitivity is <-12.5dBm; the stated optical power budget is 8dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Procurement and Asset Identification
A useful purchase order identifies the host platform, expected OEM code and optical standard separately. This prevents a module with the same housing but another wavelength, reach or identification profile from being substituted. For mixed deployments, keep one order line per OEM reference and reconcile each received unit with its intended port. For this model, the principal parameters are data rate 41.2Gbps (4x 10.3Gbps), wavelength 1310nm, rated reach 20km.
Extreme Compatibility and Factory Testing
Factory verification starts with the expected QSFP-ELR4-40G identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Ordering Information
Use QSFP-ELR4-40G as the compatibility cross-reference and QSFP-ELR4-40G as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Extreme transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QSFP-ELR4-40G, not an original Extreme-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 20km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.