H3C SFP-10GELR-31 Compatible 10G SFP+ LR Transceiver Module
Built for hosts recognizing SFP-10GELR-31, this HT-manufactured SFP+ module delivers 10G transmission at 1310nm. Its rated reach is 20km, with Duplex LC as the physical interface. The specifications and engineering guidance below support procurement teams match an equipment parts list to a clearly defined optical product, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: SFP-10GELR-31HT Part Number: SFP-10GELR-31
Product Highlights
- Compatible alternative to H3C SFP-10GELR-31
- 10G connectivity at 10.3125Gbps
- Optical wavelength: 1310nm
- Specified reach: 20km
- Duplex LC / SMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| HT Part Number | SFP-10GELR-31 |
|---|---|
| Manufacturer | HT |
| Form Factor | SFP+ |
| Max. Data Rate | 10.3125Gbps |
| Wavelength | 1310nm |
| Max. Transmission Distance | 20km |
| Connector | Duplex LC |
| Media | SMF |
| Transmitter Type | DFB |
| Receiver Type | PIN |
| TX Power | -8.2~0.5dBm |
| Receiver Sensitivity | <-14.4dBm |
| Power Budget | 6.2dB |
| Receiver Overload | 0.5dBm |
| Max. Power Consumption | ≤1W |
| Extinction Ratio | >3.5dB |
| Core Size | 9/125 µm |
| Modulation | NRZ |
| Operating Temperature | 0 to 70°C (32 to 158°F) |
| Protocols | IEEE 802.3ae, SFF-8472, SFF-8431, SFF-8432, SFP+ MSA Compliant, CPRI, eCPRI |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10G interface configuration must match the remote equipment; sharing a SFP+ housing alone does not make two transceiver types interoperable.
The single-mode link budget should include fiber attenuation, connectors, splices and panels over the intended 20km route. Keep the Duplex LC interface clean and match the remote optical standard. Consider receiver overload as well as insufficient power on short links.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -8.2~0.5dBm; receiver sensitivity is <-14.4dBm; the stated optical power budget is 6.2dB. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Procurement and Asset Identification
A useful purchase order identifies the host platform, expected OEM code and optical standard separately. This prevents a module with the same housing but another wavelength, reach or identification profile from being substituted. For mixed deployments, keep one order line per OEM reference and reconcile each received unit with its intended port. For this model, the principal parameters are data rate 10.3125Gbps, wavelength 1310nm, rated reach 20km.
H3C Compatibility and Factory Testing
Factory verification starts with the expected SFP-10GELR-31 identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Ordering Information
When ordering, specify SFP-10GELR-31, SFP-10GELR-31, quantity and intended host platform. Project labels can repeat these details for receiving and asset records. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Quality Assurance and Packaging
Each SFP-10GELR-31 compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original H3C transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies SFP-10GELR-31, not an original H3C-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 20km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.