HPE Aruba SFP-25G-PC Compatible 25G SFP28 Passive Copper Twinax Cable
A 25G direct-attached link depends on the correct host identity, interface mode and physical length. This page covers the HPE Aruba SFP-25G-PC compatible DAC series in direct-attach, including 0.5m (2ft) and 1m (3ft). Each documented length-specific OEM reference is linked separately where an individual product page is available.
Series Part Number: SFP-25G-PCHT Part Number: SFP-25G-PC
Product Highlights
- HT-manufactured compatible alternative for HPE Aruba SFP-25G-PC
- 25G aggregate connectivity at 25Gbps
- DAC
- Length configurations covered: 0.5m (2ft) and 1m (3ft)
- Conductor specification: 30AWG
Available Lengths and Corresponding Part Numbers
The documented series configuration is 0.5m (2ft) and 1m (3ft). Use the relevant OEM reference below together with the HT identity and required length when requesting a quotation. If another length carries a different OEM part number, it must be reviewed and ordered as that distinct configuration.
Compatible OEM Part Numbers
- SFP-25G-PC01
Specifications
| HT Part Number | SFP-25G-PC |
|---|---|
| Manufacturer | HT |
| Connector Type | SFP28 to SFP28 |
| Max Data Rate | 25Gbps |
| Minimum Bend Radius | 21.25mm |
| Wire AWG | 30AWG |
| Cable Length Options Covered | 0.5m (2ft) and 1m (3ft) |
| Jacket Material | PVC (OFNR) |
| Typical Power Consumption | ≤0.5W |
| Power Supply | 3.3V |
| Temperature | 0 to 70°C (32 to 158°F) |
| Protocols | IEEE 802.3, SFP28 MSA, SFF-8402, Infiniband, EIA 364-1000 |
| Application | 25G Ethernet, Data Center, 5G Wireless |
Applications and Deployment
A passive DAC reduces the connection to one factory-terminated electrical assembly. This is useful where low latency, low interface power and a short managed route matter more than optical reach. Cable gauge, connector construction and host port settings still influence whether the complete link operates reliably. For this series, the listed interface is the stated interface and the aggregate rate is 25G. The stated application is 25G Ethernet, Data Center, 5G Wireless.
Cable Construction and Routing
The specification table records the conductor specification is 30AWG; the jacket material is PVC (OFNR); the minimum bend radius is 21.25mm. Use those values when preparing the rack pathway and receiving checklist. Do not pull a connector by its cable, compress the run under tight ties or force excess length into a sharp coil. Connector protection should remain in place until the assembly is ready for insertion.
Procurement and Port-Mapping Review
A useful purchase order should identify the host platform, the expected OEM code and the exact cable length as separate pieces of information. This prevents a physically similar assembly from being substituted when the port identification or reach is different. For mixed-length installations, prepare one order line per part number and reconcile each delivered cable with its intended pair of ports. For this series, keep the interface rate, DAC construction and length-specific OEM reference together throughout that review.
HPE Aruba Compatibility and Factory Testing
Our procurement-oriented compatibility check begins with the OEM reference and ends with a live host link. We record the physical length separately from the identification configuration, so the cable supplied for this page remains the stated version rather than a generic length substitute. Series-level inspection is followed by the exact length and OEM configuration selected for dispatch. Functional verification includes link establishment and diagnostic indications where the host exposes them.
Ordering Information
For a clear bill of materials, quote the OEM reference, HT part number, length and quantity on the same line. Add the switch or server model and software release when a pre-order review is required; project labels can repeat those details for receiving and installation teams. For this series, follow the corresponding length link, quote that exact OEM part number and keep different lengths on separate order lines. HT part number SFP-25G-PC identifies the product family; the linked page provides the final length-specific identity.
Quality Assurance and Packaging
Before packing, the assembly is checked for connector condition, identification and link operation. Cables for multi-line orders can be labelled and grouped by part number, making it easier to match each length to the procurement record without opening every protective bag. Both connector ends are inspected as part of the complete assembly, and protective packing is selected to avoid tight bends during transport and storage.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.
Frequently Asked Questions
Is this an original HPE Aruba cable?
No. It is an HT-manufactured compatible cable for equipment that specifies SFP-25G-PC, not an original HPE Aruba-branded product.
Are different lengths and OEM part numbers separate products?
Yes. Where a length has its own OEM reference, follow the corresponding link above and order that exact part number on its own line. Do not substitute another length only because the connector arrangement is the same.
Does this DAC cable require separate modules at each end?
No. The connector ends and cable form one complete direct-attach assembly. The ends are not detachable standalone transceivers, and the complete product is tested together.
What information helps confirm compatibility?
Provide the equipment manufacturer and model, port type, hardware revision and software release, together with the required OEM reference, length and quantity. Breakout projects should also identify the intended lane configuration.