SFP-DD to SFP-DD-100G-AOC-10M33FT 100G SFP-DD 2 x 50G PAM4 Active Optical Cable, 10m (33ft)
The SFP-DD to SFP-DD-100G-AOC-10M33FT compatible assembly is intended for Generic equipment that requires a 100G direct-attached connection. This version is specifically 10m (33ft), with SFP-DD to SFP-DD and its own order reference. Exact length pages and equivalent brand references are linked to make multi-product procurement easier to verify.
OEM Part Number: SFP-DD to SFP-DD-100G-AOC-10M33FTHT Part Number: SFP-DD to SFP-DD-100G-AOC-10M33FT
Product Highlights
- HT-manufactured AOC assembly in 10m (33ft)
- 100G connectivity at 100Gbps
- Interface configuration: SFP-DD to SFP-DD
- Fixed length and part number: 10m (33ft), SFP-DD to SFP-DD-100G-AOC-10M33FT
- Cable construction: OM4
- Maximum power consumption: ≤3.5W
- Minimum bend radius: 60mm
Specifications
| HT Part Number | SFP-DD to SFP-DD-100G-AOC-10M33FT |
|---|---|
| Manufacturer | HT |
| Connector Type | SFP-DD to SFP-DD |
| Max Data Rate | 100Gbps |
| Cable Length | 10m (33ft) |
| Cable Type | OM4 |
| Wavelength | 850nm |
| Minimum Bend Radius | 60mm |
| Transmitter Type | VSCEL |
| Receiver Type | PIN |
| Power Consumption | ≤3.5W |
| Power supply | 3.5V |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Modulation Format | 2x 50G-PAM4 to 2x 50G-PAM4 |
| DDM/DOM | Supported |
| Commercial Temperature | 0 to 70°C (32 to 158°F) |
| Protocols | SFP-DD MSA, SFP-DD MIS |
Signal and Lane Configuration
The listed modulation format is 2x 50G-PAM4 to 2x 50G-PAM4. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.
Network and Protocol Considerations
The intended application is determined by the host interface and protocol support. Listed interface and protocol references include SFP-DD MSA, SFP-DD MIS. Confirm that the host firmware and port configuration support the same operating mode.
Integrated Optical Assembly
The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.
Length Selection and Installation Planning
With 10m (33ft) available, the installer has more routing freedom but also more cable to control. Determine where any remaining service loop will be stored, preserve the stated bend radius and keep the loop away from sharp edges and hot exhaust. The integrated optical cable and both optical engines should remain accessible for inspection and removal. Within this family, SFP-DD to SFP-DD-100G-AOC-7M23FT is shorter at 7m (23ft), while SFP-DD to SFP-DD-100G-AOC-15M49FT is the next longer choice at 15m (49ft); comparing those two boundaries helps avoid both tension and unnecessary slack.
Position Within the Length Range
SFP-DD to SFP-DD-100G-AOC-10M33FT occupies the middle of this family between SFP-DD to SFP-DD-100G-AOC-7M23FT at 7m (23ft) and SFP-DD to SFP-DD-100G-AOC-15M49FT at 15m (49ft). It adds 3m over the shorter option for extra routing clearance, while the next longer version adds another 5m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.
Procurement and Port-Mapping Review
A useful purchase order should identify the host platform, the expected OEM code and the exact cable length as separate pieces of information. This prevents a physically similar assembly from being substituted when the port identification or reach is different. For mixed-length installations, prepare one order line per part number and reconcile each delivered cable with its intended pair of ports. For this assembly, the minimum bend radius is 60mm; the stated power consumption is ≤3.5W.
Power and Thermal Planning
The rated power consumption is ≤3.5W. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.
Cable Construction and Routing
This assembly uses minimum bend radius 60mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.
Generic Compatibility and Factory Testing
Our procurement-oriented compatibility check begins with the OEM reference and ends with a live host link. We record the physical length separately from the identification configuration, so the cable supplied for this page remains the stated version rather than a generic length substitute. Both connectors are examined before the operating test, which includes receive activity and diagnostic indications.
Ordering Information
For a clear bill of materials, quote the OEM reference, HT part number, length and quantity on the same line. Add the switch or server model and software release when a pre-order review is required; project labels can repeat those details for receiving and installation teams. Keep SFP-DD to SFP-DD-100G-AOC-10M33FT associated with 10m (33ft) throughout the order and receiving record.
Quality Assurance and Packaging
Before packing, the assembly is checked for connector condition, identification and link operation. Cables for multi-line orders can be labelled and grouped by part number, making it easier to match each length to the procurement record without opening every protective bag. Neutral packaging and customer-specific packing documentation are available on request.
Frequently Asked Questions
Is this an original equipment manufacturer cable?
No. It is manufactured by HT under our own manufacturer identity.
Will any matching connector operate at the same speed?
Not necessarily. Both hosts must support the stated rate, identification, lane mapping and any required breakout configuration; mechanical compatibility alone is insufficient.
What details assist a compatibility review?
Provide the equipment manufacturer, model, port type, hardware revision and software release, together with the OEM reference, required length and quantity.
How should an unused assembly be stored?
Protect both connector ends, keep the cable in a loose bend-safe coil and retain its part-number label so the length and compatibility identity remain traceable.
Shipping and Lead Time
Available stock is generally dispatched within one to three working days after order confirmation, with production lead times advised for larger quantities. Delivery can be arranged by courier, air freight or sea freight, and goods may instead be handed to an appointed forwarder or shipped on the customer’s courier account.