SFP+ to SFP+-10G-AOC-50M164FT 10G SFP+ Industrial Active Optical Cable, 50m (164ft)
The SFP+ to SFP+-10G-AOC-50M164FT compatible assembly is intended for Generic equipment that requires a 10G direct-attached connection. This version is specifically 50m (164ft), with SFP+ to SFP+ and its own order reference. Exact length pages and equivalent brand references are linked to make multi-product procurement easier to verify.
OEM Part Number: SFP+ to SFP+-10G-AOC-50M164FTHT Part Number: SFP+ to SFP+-10G-AOC-50M164FT
Product Highlights
- HT-manufactured AOC assembly in 50m (164ft)
- Interface configuration: SFP+ to SFP+
- Fixed length and part number: 50m (164ft), SFP+ to SFP+-10G-AOC-50M164FT
- Minimum bend radius: 30mm
Specifications
| HT Part Number | SFP+ to SFP+-10G-AOC-50M164FT |
|---|---|
| Manufacturer | HT |
| Connector Type | SFP+ to SFP+ |
| Max Supply Voltage | 3.45 V |
| Minimum Bend Radius | 30mm |
| Cable Length | 1~300m@OM3 MMF |
| Wavelength | 850nm |
| Built-in CDR | NO |
| Transmitter Type | VSCEL |
| Receiver Type | PIN |
| Modulation | NRZ |
| Bit Error Rate | 1E-12 |
| Jacket Material | OFNP |
| Built-in FEC | NO |
| Protocols | SFF-8431,10GBASE Ethernet, Fibre Channel |
| Operation temperature | -40 to 85°C (-40 to 185°F) |
Cable Construction and Routing
This assembly uses OFNP jacket, minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.
Integrated Optical Assembly
The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.
Length Selection and Installation Planning
With 50m (164ft) available, the installer has more routing freedom but also more cable to control. Determine where any remaining service loop will be stored, preserve the stated bend radius and keep the loop away from sharp edges and hot exhaust. The integrated optical cable and both optical engines should remain accessible for inspection and removal. Within this family, SFP+ to SFP+-10G-AOC-1M3FT is shorter at 1m (3ft), while SFP+ to SFP+-10G-AOC-70M230FT is the next longer choice at 70m (230ft); comparing those two boundaries helps avoid both tension and unnecessary slack.
Position Within the Length Range
SFP+ to SFP+-10G-AOC-50M164FT occupies the middle of this family between SFP+ to SFP+-10G-AOC-1M3FT at 1m (3ft) and SFP+ to SFP+-10G-AOC-70M230FT at 70m (230ft). It adds 49m over the shorter option for extra routing clearance, while the next longer version adds another 20m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.
Procurement and Port-Mapping Review
A useful purchase order should identify the host platform, the expected OEM code and the exact cable length as separate pieces of information. This prevents a physically similar assembly from being substituted when the port identification or reach is different. For mixed-length installations, prepare one order line per part number and reconcile each delivered cable with its intended pair of ports. For this assembly, the minimum bend radius is 30mm; the jacket material is OFNP.
Network and Protocol Considerations
The intended application is determined by the host interface and protocol support. Listed interface and protocol references include SFF-8431,10GBASE Ethernet, Fibre Channel. Confirm that the host firmware and port configuration support the same operating mode.
Generic Compatibility and Factory Testing
Our procurement-oriented compatibility check begins with the OEM reference and ends with a live host link. We record the physical length separately from the identification configuration, so the cable supplied for this page remains the stated version rather than a generic length substitute. Both connectors are examined before the operating test, which includes receive activity and diagnostic indications.
Ordering Information
For a clear bill of materials, quote the OEM reference, HT part number, length and quantity on the same line. Add the switch or server model and software release when a pre-order review is required; project labels can repeat those details for receiving and installation teams. Quantity and any labeling instructions should be attached specifically to SFP+ to SFP+-10G-AOC-50M164FT.
Quality Assurance and Packaging
Before packing, the assembly is checked for connector condition, identification and link operation. Cables for multi-line orders can be labelled and grouped by part number, making it easier to match each length to the procurement record without opening every protective bag. Standard protective packing is used by default, with project documentation arranged when requested.
Frequently Asked Questions
Is this an original equipment manufacturer cable?
No. It is manufactured by HT under our own manufacturer identity.
What details assist a compatibility review?
Provide the equipment manufacturer, model, port type, hardware revision and software release, together with the OEM reference, required length and quantity.
How should an unused assembly be stored?
Protect both connector ends, keep the cable in a loose bend-safe coil and retain its part-number label so the length and compatibility identity remain traceable.
Can different brands be connected with the same assembly?
Only where both hosts explicitly support the complete interface and compatibility arrangement. Document each end and select the appropriate brand-specific product when required.
Shipping and Lead Time
Available stock is generally dispatched within one to three working days after order confirmation, with production lead times advised for larger quantities. Delivery can be arranged by courier, air freight or sea freight, and goods may instead be handed to an appointed forwarder or shipped on the customer’s courier account.