Brocade SFP1G-SX-31 Compatible 1G SFP Transceiver Module
The SFP1G-SX-31 compatible module serves equipment requiring a 1G SFP interface with 1310nm optics and a 2km rating. Connection is through Duplex LC. Product data, application guidance and factory verification are presented together to support procurement teams match an equipment parts list to a clearly defined optical product.
OEM Part Number: SFP1G-SX-31HT Part Number: SFP1G-SX-31
Product Highlights
- Compatible alternative to Brocade SFP1G-SX-31
- 1G connectivity at 1.25Gbps
- Optical wavelength: 1310nm
- Specified reach: 2km
- Duplex LC / SMF/MMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| HT Part Number | SFP1G-SX-31 |
|---|---|
| Manufacturer | HT |
| Form Factor | SFP |
| Max. Data Rate | 1.25Gbps |
| Connector | Duplex LC |
| Max. Cable Distance | 2km |
| Media | SMF/MMF |
| Wavelength | 1310nm |
| Modulation | NRZ |
| Power Consumption | < 1W |
| Transmitter Type | FP |
| Receiver Type | PIN-TIA |
| TX Power | -9~-3dBm |
| Receiver Sensitivity | < -21dBm |
| BER | 1E-12 |
| DOM Support | Yes |
| Protocols | SFF-8472, MSA, IEEE 802.3 |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| MTTF | 80,226 Hours[Condition |
| 30°C Reference Operating Condition, Based on Accelerated Life Testing] | Warranty |
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The Duplex LC interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 1G interface configuration must match the remote equipment; sharing a SFP housing alone does not make two transceiver types interoperable.
For this multimode module, confirm fiber grade, modal bandwidth and total loss before commissioning. The 2km figure applies only under suitable cabling conditions. Inspect every Duplex LC mating point and match the remote optical standard.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -9~-3dBm; receiver sensitivity is < -21dBm. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Procurement and Asset Identification
A useful purchase order identifies the host platform, expected OEM code and optical standard separately. This prevents a module with the same housing but another wavelength, reach or identification profile from being substituted. For mixed deployments, keep one order line per OEM reference and reconcile each received unit with its intended port. For this model, the principal parameters are data rate 1.25Gbps, wavelength 1310nm, rated reach 2km.
Brocade Compatibility and Factory Testing
Compatibility testing for SFP1G-SX-31 combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Ordering Information
Quote HT part number SFP1G-SX-31 together with OEM reference SFP1G-SX-31 and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Quality Assurance and Packaging
Each SFP1G-SX-31 compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Brocade transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies SFP1G-SX-31, not an original Brocade-branded module.
Which fiber and connector are required?
Use Duplex LC with SMF/MMF. The specified maximum reach is 2km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.