Juniper Networks SRX-CFP-100G-SR10 Compatible 100G CFP SR10 Transceiver Module
Built for hosts recognizing SRX-CFP-100G-SR10, this HT-manufactured CFP module delivers 100G transmission at 850nm. Its rated reach is 150m on OM4, 100m on OM3, with its specified interface as the physical interface. The specifications and engineering guidance below support procurement teams match an equipment parts list to a clearly defined optical product, while keeping HT manufacture separate from the OEM cross-reference.
OEM Part Number: SRX-CFP-100G-SR10HT Part Number: CFP-SR10-100G
Product Highlights
- Compatible alternative to Juniper Networks SRX-CFP-100G-SR10
- 100G connectivity at 103.1 Gbp
- Optical wavelength: 850nm
- Specified reach: 150m on OM4, 100m on OM3
- MMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| Juniper Networks Compatible | SRX-CFP-100G-SR10 |
|---|---|
| Manufacturer | HT |
| HT Part Number | CFP-SR10-100G |
| Form Factor | CFP |
| Max Data Rate | 103.1 Gbp |
| Wavelength | 850nm |
| Max Cable Distance | 150m@OM4, 100m@OM3 |
| Interface | MTP/MPO-24 |
| Optical Components | 10x VCSEL |
| Media | MMF |
| DOM Support | Yes |
| Modulation (Electrical) | 10x 10G-NRZ |
| Modulation (Optical) | 10x 10G-NRZ |
| Protocols | MSA Compliant |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
Applications and Optical Link Design
Typical deployments include switch-to-switch, switch-to-server and aggregation links inside a data hall or between adjacent equipment rooms. The interface connects to the specified multimode cabling, and the stated reach depends on fiber grade and link loss. Keep this interface on the matching multimode optical standard rather than connecting it directly to a single-mode wavelength or reach variant.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a CFP housing alone does not make two transceiver types interoperable.
The multimode channel should use the fiber grade associated with the stated 150m on OM4, 100m on OM3 reach. Keep the end faces clean and avoid tight bends. Different multimode standards are not interchangeable merely because they share a connector.
Optical Acceptance, Diagnostics and Handling
Use the electrical and optical limits in the specification table as the acceptance reference for this model. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Procurement and Asset Identification
A useful purchase order identifies the host platform, expected OEM code and optical standard separately. This prevents a module with the same housing but another wavelength, reach or identification profile from being substituted. For mixed deployments, keep one order line per OEM reference and reconcile each received unit with its intended port. For this model, the principal parameters are data rate 103.1 Gbp, wavelength 850nm, rated reach 150m on OM4, 100m on OM3.
Juniper Networks Compatibility and Factory Testing
Compatibility testing for SRX-CFP-100G-SR10 combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Ordering Information
Use SRX-CFP-100G-SR10 as the compatibility cross-reference and CFP-SR10-100G as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Juniper Networks transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies SRX-CFP-100G-SR10, not an original Juniper Networks-branded module.
Which fiber and connector are required?
Use the specified optical connector with MMF. The specified maximum reach is 150m on OM4, 100m on OM3, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.