Generic DW-SFP10G40-C Compatible 10G SFP+ Transceiver Module
The DW-SFP10G40-C compatible module serves equipment requiring a 10G SFP+ interface with 1529.16~1567.13nm (Tunable） optics and a 40km rating. Connection is through Duplex LC. Product data, application guidance and factory verification are presented together to support procurement teams match an equipment parts list to a clearly defined optical product.
OEM Part Number: DW-SFP10G40-CHT Part Number: DW-SFP10G40-C
Product Highlights
- Compatible alternative to Generic DW-SFP10G40-C
- 10G connectivity at 11.3Gbps
- Optical wavelength: 1529.16~1567.13nm (Tunable）
- Specified reach: 40km
- Duplex LC / SMF interface
- Operating temperature: 0 to 70°C (32 to 158°F)
- Factory compatibility verification and optical performance testing before shipment
Specifications
| HT Part Number | DW-SFP10G40-C |
|---|---|
| Manufacturer | HT |
| Form Factor | SFP+ |
| Max Data Rate | 11.3Gbps |
| Connector | Duplex LC |
| Max Cable Distance | 40km |
| Media | SMF |
| Wavelength | 1529.16~1567.13nm (Tunable） |
| Modulation | NRZ |
| Power Consumption | ≤2.1W |
| Transmitter Type | Monolithic MZM Tunable TOSA |
| Receiver Type | PIN |
| Power Budget | 15dB（@9.95Gbps~10.7Gbps）18dB（@11.3Gbps） |
| Extinction Ratio | 8.2dB |
| CDR | Yes |
| BER | 1E-12 |
| TX Power | -1~3dBm |
| Receiver Overload | -7dBm |
| EMC (Electro Magnetic Compatibility) | Supported |
| DDM/DOM Support | YES |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Inbuilt FEC | NO |
| Protocols | IEEE 802.3ae CL 52 MSA SFF-8472 MSA SFF-8431 MSA SFF-8690ITU-T G.698.1 |
| Application | Ethernet, SONET/SDH |
Applications and Optical Link Design
This coherent interface is suited to data-center interconnect, metro transport and managed DWDM links where the host platform supports the stated modulation and FEC modes. Design the optical line around the actual launch power, receiver range, OSNR requirement and span loss; the stated reach is not a substitute for a link-budget calculation. Use matching coherent modules and the appropriate DWDM channel plan at both ends.
Before deployment, check the host port type, supported data rate and firmware requirements. The 10G interface configuration must match the remote equipment; sharing a SFP+ housing alone does not make two transceiver types interoperable.
Coherent deployment requires a line-system review, not merely a matching connector. Confirm the DWDM channel, launch-power range, receiver limits, OSNR and FEC mode at both ends. Span loss and amplifier operation must remain inside the supported envelope, and stated reach should be validated against the actual route.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -1~3dBm; the stated optical power budget is 15dB（@9.95Gbps~10.7Gbps）18dB（@11.3Gbps）. Digital diagnostics make later maintenance easier when baseline values are captured at installation. Save the initial readings with the port and OEM reference, then investigate meaningful changes rather than reacting to a single transient value. Diagnostic support depends on the host as well as the module, so unavailable fields should be confirmed with the platform documentation. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Procurement and Asset Identification
A useful purchase order identifies the host platform, expected OEM code and optical standard separately. This prevents a module with the same housing but another wavelength, reach or identification profile from being substituted. For mixed deployments, keep one order line per OEM reference and reconcile each received unit with its intended port. For this model, the principal parameters are data rate 11.3Gbps, wavelength 1529.16~1567.13nm (Tunable）, rated reach 40km.
Generic Compatibility and Factory Testing
Compatibility testing for DW-SFP10G40-C combines identification with a live link and available transmit, receive and alarm information. Connector condition is inspected separately. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Ordering Information
Use DW-SFP10G40-C as the compatibility cross-reference and DW-SFP10G40-C as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Quality Assurance and Packaging
Before packing, the module receives interface inspection, identification and link checks. Protective packaging avoids pressure on the connector and latch. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original equipment manufacturer transceiver?
No. It is an HT-manufactured compatible transceiver supplied under our own manufacturer identity, not an original equipment manufacturer module.
Which fiber and connector are required?
Use Duplex LC with SMF. The specified maximum reach is 40km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.