Generic QSFP-CWDM4-100G Compatible 100G QSFP28 CWDM4 Transceiver Module
The QSFP-CWDM4-100G compatible module serves equipment requiring a 100G QSFP28 interface with 1271nm, 1291nm, 1311nm and 1331nm optics and a 2km rating. Connection is through Duplex LC/UPC. Product data, application guidance and factory verification are presented together to support procurement teams match an equipment parts list to a clearly defined optical product.
OEM Part Number: QSFP-CWDM4-100GHT Part Number: QSFP-CWDM4-100G
Product Highlights
- Compatible alternative to Generic QSFP-CWDM4-100G
- 100G connectivity at 103.125Gbps (4x 25.78Gbps)
- Optical wavelength: 1271nm, 1291nm, 1311nm and 1331nm
- Specified reach: 2km
- Duplex LC/UPC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | QSFP-CWDM4-100G |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP28 |
| Max. Data Rate | 103.125Gbps (4x 25.78Gbps) |
| Wavelength | 1271nm, 1291nm, 1311nm and 1331nm |
| Max. Cable Distance | 2km |
| Connector | Duplex LC/UPC |
| Media | SMF |
| Transmitter Type | 4 x CWDM DML (DFB) |
| Receiver Type | PIN |
| TX Power | -6.5~2.5dBm |
| Minimum Receiver Power | -11.5dBm |
| Power Budget | 5dB |
| Receiver Overload | 2.5dBm |
| Max. Power Consumption | 3.5W |
| Extinction Ratio | >3.5dB |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Modulation (Electrical) | 4x 25G-NRZ |
| Modulation (Optical) | 4x 25G-NRZ |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Inbuilt FEC | Yes |
| Bit Error Ratio (BER) | 1E-12 |
| MTBF | 12,800,000 Hours (@40°C, 60% CL) |
| Protocols | QSFP28 MSA, SFF-8636, IEEE 802.3ba, IEEE 802.3bm, CAUI-4 |
Applications and Optical Link Design
Use this module for equipment interconnection over the specified single-mode fiber plant, including enterprise backbone, campus, metro or data-center interconnect links according to its rated distance. Confirm that both ends use the same optical standard and wavelength plan, and allow for connector, splice and patch-panel loss within the stated power budget.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a QSFP28 housing alone does not make two transceiver types interoperable.
For this 1271nm, 1291nm, 1311nm and 1331nm interface, verify channel spacing and filter compatibility. Passive filters add loss even without active equipment, so assess 2km using the complete channel rather than fiber distance alone.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -6.5~2.5dBm; the stated optical power budget is 5dB. During commissioning, record the host diagnostic readings after the link has stabilized and compare them with those limits. DOM values are useful operational indicators, but they do not replace calibrated optical measurements when a link is marginal. Investigate unexpected loss through connector inspection, cleaning and a channel measurement before replacing the module. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Procurement and Asset Identification
A useful purchase order identifies the host platform, expected OEM code and optical standard separately. This prevents a module with the same housing but another wavelength, reach or identification profile from being substituted. For mixed deployments, keep one order line per OEM reference and reconcile each received unit with its intended port. For this model, the principal parameters are data rate 103.125Gbps (4x 25.78Gbps), wavelength 1271nm, 1291nm, 1311nm and 1331nm, rated reach 2km.
Generic Compatibility and Factory Testing
Factory verification starts with the expected QSFP-CWDM4-100G identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Ordering Information
Quote HT part number QSFP-CWDM4-100G together with OEM reference QSFP-CWDM4-100G and quantity. Add the host model and software release when pre-order verification is required. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Quality Assurance and Packaging
Each QSFP-CWDM4-100G compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original equipment manufacturer transceiver?
No. It is an HT-manufactured compatible transceiver supplied under our own manufacturer identity, not an original equipment manufacturer module.
Which fiber and connector are required?
Use Duplex LC/UPC with SMF. The specified maximum reach is 2km, subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.