Nokia QSFP-ZRBD-100G-S Compatible 100G QSFP28 Transceiver Module
The QSFP-ZRBD-100G-S compatible module serves equipment requiring a 100G QSFP28 interface with 1528.77~1566.72nm optics and a 80km (unamplified)300km (amplified) rating. Connection is through Duplex LC/UPC. Product data, application guidance and factory verification are presented together to support procurement teams match an equipment parts list to a clearly defined optical product.
OEM Part Number: QSFP-ZRBD-100G-SHT Part Number: QSFP-ZRBD-100G-S
Product Highlights
- Compatible alternative to Nokia QSFP-ZRBD-100G-S
- 100G connectivity at 100Gbps
- Optical wavelength: 1528.77~1566.72nm
- Specified reach: 80km (unamplified)300km (amplified)
- Duplex LC/UPC / SMF interface
- Digital diagnostic monitoring: Supported
- Operating temperature: 0 to 70°C (32 to 158°F)
Specifications
| HT Part Number | QSFP-ZRBD-100G-S |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP28 |
| Max. Data Rate | 100Gbps |
| Wavelength | 1528.77~1566.72nm |
| Max. Cable Distance | 80km (unamplified)300km (amplified) |
| Connector | Duplex LC/UPC |
| Media | SMF |
| Transmitter Type | Coherent |
| Max. Power Consumption | 7W |
| TX Power | -8~-5dBm |
| Minimum Receiver Power | -31.5dBm |
| Power Budget | 23.5dB |
| Receiver Overload | 3dBm |
| DDM/DOM | Supported |
| Inbuilt FEC | Host: RS FEC or NoneMedia: SC FEC |
| Modulation (Electrical) | NRZ |
| Modulation (Optical) | DP-DQPSK |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Application | Ethernet、OTN |
| Protocols | SFF-8661 Rev.2.5, QSFP-DD MSA Rev 7.1, Type 2A, IEEE 802.3-2022, IEEE 802.3-2022 100GBASE-ZR, CMIS Rev5.2 |
Applications and Optical Link Design
This coherent interface is suited to data-center interconnect, metro transport and managed DWDM links where the host platform supports the stated modulation and FEC modes. Design the optical line around the actual launch power, receiver range, OSNR requirement and span loss; the stated reach is not a substitute for a link-budget calculation. Use matching coherent modules and the appropriate DWDM channel plan at both ends.
Before deployment, check the host port type, supported data rate and firmware requirements. The 100G interface configuration must match the remote equipment; sharing a QSFP28 housing alone does not make two transceiver types interoperable.
Coherent deployment requires a line-system review, not merely a matching connector. Confirm the DWDM channel, launch-power range, receiver limits, OSNR and FEC mode at both ends. Span loss and amplifier operation must remain inside the supported envelope, and stated reach should be validated against the actual route.
Optical Acceptance, Diagnostics and Handling
For this model, the specified transmit-power range is -8~-5dBm; the stated optical power budget is 23.5dB. A sound acceptance record includes link state, diagnostic temperature, supply voltage and transmit or receive levels where the host exposes them. Compare the readings with the stated ranges rather than treating any received light as proof of adequate margin. Persistent alarms or borderline values should trigger an end-face and complete-channel inspection. Diagnostic monitoring is listed as Supported. Before every insertion, keep dust caps in place until the patch lead is ready, avoid touching the optical end face and use an appropriate inspection and cleaning procedure. Do not look into an active optical interface.
Procurement and Asset Identification
A useful purchase order identifies the host platform, expected OEM code and optical standard separately. This prevents a module with the same housing but another wavelength, reach or identification profile from being substituted. For mixed deployments, keep one order line per OEM reference and reconcile each received unit with its intended port. For this model, the principal parameters are data rate 100Gbps, wavelength 1528.77~1566.72nm, rated reach 80km (unamplified)300km (amplified).
Nokia Compatibility and Factory Testing
Factory verification starts with the expected QSFP-ZRBD-100G-S identity and finishes with an operating host link. EEPROM data, diagnostic visibility and the stated optical parameters are assessed together. Equipment model, hardware revision and software release can be reviewed before dispatch where platform behavior is uncertain.
Ordering Information
Use QSFP-ZRBD-100G-S as the compatibility cross-reference and QSFP-ZRBD-100G-S as the HT ordering identity. Keep other reaches or wavelength directions on separate order lines. Neutral labels, customer packaging and project-specific compatibility review are available on request.
Quality Assurance and Packaging
Each QSFP-ZRBD-100G-S compatible module is inspected, powered up and functionally checked before protective packing. Dust caps and individual trays shield the interface during transport. Customer references, rack groups and project packing lists can be added for volume orders.
Frequently Asked Questions
Is this an original Nokia transceiver?
No. It is an HT-manufactured compatible alternative for equipment that specifies QSFP-ZRBD-100G-S, not an original Nokia-branded module.
Which fiber and connector are required?
Use Duplex LC/UPC with SMF. The specified maximum reach is 80km (unamplified)300km (amplified), subject to fiber quality and total link loss.
Can it be mixed with another wavelength or reach version?
Only when the two ends share the same optical standard, wavelength plan and supported data rate. Check the exact part numbers and link budget rather than relying only on the module form factor.
Shipping and Lead Time
Standard configurations normally ship within one to three working days, with production lead times confirmed for larger quantities. International courier, air freight and sea freight are available; customer courier accounts and nominated forwarders are accepted.